PXL-500 Controller Specifications

PXL-500 Controller Specifications

Specifications

1.0 Unit Dimensions

• PXL-500/PXL-510 controller PCB
- 6.75 inches high by 6.00 inches wide by 1.75 inches deep, including wiring connectors
- (17.15 cm by 15.25 cm by 4.45 cm)

• PXL-500/PXL-510 controller PCB with an LCD-1 Alpha/Numeric Display
- 7.70 inches high by 6.00 inches wide by 1.75 inches deep, including wiring connectors
- (19.60 cm by 15.25 cm by 4.45 cm)

• PXL-500/PXL-510 controller PCB with an SB-593 Satellite Board (with or without an LCD-1 Alpha/Numeric Display)
- 7.25 inches high by 6.00 inches wide by 1.75 inches deep, including wiring connectors
- (18.45 cm by 15.25 cm by 4.45 cm)

• Enclosure - 13 inches high by 9 inches wide by 4 inches deep
- (33.02 cm by 22.86 cm by 10.16 cm)


2.0 Operating Temperature/Humidity Range

• 0°F to 140°F (-18°C to 60°C)
• 0% to 90% Relative Humidity, non-condensing


3.0 Controller Power Requirements

• 12 VDC @ 1 A Current Draw
• maximum current draw 270 mA for a controller plus reader current draw (refer to Table 1 for Reader current draw)
• 120 mA max for a PXL-500/PXL-510 Controller • 150 mA max for an SB-593 Satellite Board


4.0 Reader Current Draw



Reader Type



MS-3000
MS-4000
MS-5000
MS-7000
Current Draw
50 mA
50 mA
100 mA
100 mA

Note: If an electronic locking device (such as a magnetic lock, a door strike, or similar device) is to be driven by the same power supply as the PXL-500/PXL-510 controller, please ensure the power supply provides enough current to drive every device connected to that supply plus an adequate safety margin. AC power is not recommended.


5.0 Controller Memory Retention

• 5 year lithium battery back up to support controller RAM and real-time clock


6.0 Output Relay Contact Rating

• 1 Amp @ 24 VDC


7.0 Input Device Configuration - 3 Inputs

• Door Sense normally closed
• Request to Exit normally open
• Global Unlock normally open, or Auxiliary RTE A-Door normally open


    • Related Articles

    • PXL-500 Controller Data Sheet

        PXL-500 Controller Data Sheet
    • SB-593 Satellite Board Specifications

      Specifications: Unit Dimensions • PXL-250/PXL-500/PXL-510 controller PCB with an SB-593 Satellite Board (with or without an LCD-1 Alpha/ Numeric Display): - 7.25 inches high by 6.00 inches wide by 1.75 inches deep, including wiring connectors - ...
    • PXL Controller Firmware Upgrade

      PXL Controller Firmware Upgrade Procedure 1.0 Introduction PXL controllers do not have flash firmware and so they require a physical chip change. The PXL Firmware Upgrade ship kit comes with a chip extraction tool to assist with the removal and ...
    • PXL-500 Controller Offline Flowchart

      This flowchart is aimed at helping installers to troubleshooting an offline PXL-500 controller network.
    • PXL-500 Controller Factory Reset

      PXL-500 Standard Factory Reset Procedure If you're turning controller power on for the first time, or have just changed the EPROM/PIC, the PXL-500/PXL-510 controller RAM must be reset before performing any other action... this clears any spurious ...