SB-593 Satellite Board Specifications

SB-593 Satellite Board Specifications

Specifications:

Unit Dimensions

• PXL-250/PXL-500/PXL-510 controller PCB with an SB-593 Satellite Board (with or without
an LCD-1 Alpha/ Numeric Display):

- 7.25 inches high by 6.00 inches wide by 1.75 inches deep, including wiring connectors
- (18.45 cm by 15.25 cm by 4.45 cm)

Enclosure
- 9.70 inches high by 8.20 inches wide by 2.60 inches deep
- (24.65 cm by 20.85 cm by 6.60 cm)


Operating Temperature/Humidity Range
• 0°F to 140°F (-18°C to 60°C)
• 0% to 90% Relative Humidity, non-condensing


Controller with Satellite Board Power Requirements
• 12 VDC @ 1 Amp


Current Draw
• maximum current draw 270 mA for a controller plus reader current draw (refer to Table 1 for Reader current draw) • 120 mA max for a PXL-250/PXL-500/PXL-510 Controller • 150 mA max for an SB-593 Satellite Board


Table 1: Reader Current Draw      
                                                                             Reader Type


MS-3000
MS-4000
MS-5000
MS-7000
Current Draw
50 mA
50 mA
100 mA
200 mA


Output Relay Contact Rating
  1. 1 Amp @ 24 VDC


Input Device Configuration
• Door Sense normally closed
• Request to Exit normally open
• Global Unlock normally open, or Auxiliary RTE A-Door normally open


Cable Requirements
• two conductor, AWG 22 or a larger gauge for all input connections
• two conductor, AWG 18 or a larger gauge for all output connections

Note: The Lock Output relay may require a heavier gauge of wire depending upon the
current demands of the lock and the length of the lock wiring run.




    • Related Articles

    • SB-593 Hardware Installation Guide

      1.0 Wiring Diagram 2.0 Specifications: Unit Dimensions • PXL-250/PXL-500/PXL-510 controller PCB with an SB-593 Satellite Board (with or without an LCD-1 Alpha/ Numeric Display): - 7.25 inches high by 6.00 inches wide by 1.75 inches deep, including ...
    • PXL-500 Controller Specifications

      Specifications 1.0 Unit Dimensions • PXL-500/PXL-510 controller PCB - 6.75 inches high by 6.00 inches wide by 1.75 inches deep, including wiring connectors - (17.15 cm by 15.25 cm by 4.45 cm) • PXL-500/PXL-510 controller PCB with an LCD-1 ...
    • Input/Output (I/O) Control - Using PXL-500 Controllers

      I/O (Input/Output) Basic Linkage - Using PXLs Using Doors.NET v3.5.1.21 and higher, you can apply basic I/O linkage actions to a PXL-500 controller which has an SB-593 satellite board connected to it. The SB-593 provides a PXL-500 with an additional ...
    • PXL Controller Firmware Upgrade

      PXL Controller Firmware Upgrade Procedure 1.0 Introduction PXL controllers do not have flash firmware and so they require a physical chip change. The PXL Firmware Upgrade ship kit comes with a chip extraction tool to assist with the removal and ...
    • PXL-500 Firmware Chip Change Procedure

      PXL-500 Firmware Chip Extraction Tool The AMP chip extraction tool is provided to assist in the removal and replacement of chip carriers used in the Keri Systems’ PXL-500/PXL-510 and Entraguard controllers. Upgrade the EPROM Note: If the PXL ...