Hardware Installation
KE-8 Metal Enclosure Installation Guide
Section 1 – Specifications Section 2 – Wall Mounting the Enclosure Section 3 – Controller Installation Section 4 – Tamper Relay Board Mounting Section 5 – Wire Routing Section 6 – Keri Contact Information The KE-8 Controller Enclosure handles up to ...
PXL-500 - Recommended USB-Serial Adapters
Because of the vast number of different manufacturers and models of USB-to-Serial adapters it would be impossible for us to verify the functionality of each one. Here is a list of specific models of adapter that are approved and recommended for use ...
SB-593 Hardware Installation Guide
1.0 Important Note: Keri Public Statement on the Amazon Key Keri does not support the use of the Amazon Key on Keri controllers. The Amazon Key does not interface to Keri products in a way that allows the Building Owner or Manager to maintain ...
PXL-500 and Entraguard - Earth-Grounding Reference Guide
Introduction You should make a quality earth ground connection to all Keri PXL controllers to ensure the best possible operating conditions. An earth ground brings all electrically neutral lines to the earth's surface potential (essentially to a zero ...
PXL-500 - LED Definitions
1.0 Reader LED Responses to Access Control Events During day-to-day activity, the reader will respond to access control events in a specific manner. The Table below provides a summary of the reader's LED and beeper actions during access control ...
PXL-500 Connector Tolerance Notification
Standalone PDF - PXL-500 Connector Tolerance Notification.
PXL-500 Hardware Installation Guide
1.0 Introduction This document contains basic information for the installation of the PXL-500 Controller. 2.0 Important Note: Keri Public Statement on the Amazon Key Keri does not support the use of the Amazon Key on Keri controllers. The Amazon Key ...
KE-1 Metal Enclosure Installation Guide
1.0 Introduction This installation guide is for the NXT/PXL KE-1 metal enclosure. It includes mounting dimensions and environmental ratings. It is intended to provide a secure enclosure for the PXL-500 controller, NXT and NXT-MSC 2 or 4-door ...
PXL-500 Firmware Chip Change Procedure
1.0 Introduction PXL controllers do not have flash firmware and so they require a physical chip change. The PXL Firmware Upgrade ship kit comes with a chip extraction tool to assist with the removal and replacement of chips - failure to use the ...
PXL-500 Controller Address Change
PXL - Change Controller Address Viewing the Controller's Address To view the controller address, click S1. The controller address will appear on the display for a few seconds. Setting the Controller's Address To set the desired operating address ...
PXL-500 Controller Factory Reset
1.0 PXL-500 Standard Controller RAM Reset If you're turning controller power on for the first time, or have just changed the EPROM/PIC, the PXL-500/PXL-510 controller RAM must be reset before performing any other action... this clears any spurious ...
Powering The PXL-500 Controller for the First Time
Note: Verify the earth ground1 has been connected at pin 3 of TB-2 before turning the power on for the first time. Note: Do not connect the 12 VDC power supply’s terminal block output to the TB-2 connector on the PXL-500/PXL-510 controller until you ...
PXL-500 Wiring Instructions
Terminal Blocks Connecting Wires and Removing Terminal Blocks Note: Screws on terminal blocks must be tightened securely. Connecting the Earth Ground and the 12 VDC Power Note: TB2 is colored red to make it easier to tell it apart from the network ...
PXL-500 Controller Installation Guidelines
When Installing Controllers DO • If using modems for communication plan ahead to meet power and any telephone requirements for your system (1 phone line for the modem connected to the host computer and one for each master PXL-500/PXL-510 in each ...
PXL-500 Controller Cable Requirements
Cable Requirements RS-232 Serial Cable • four conductor, shielded, stranded, AWG 24 wire (Belden 9534 or a larger gauge) • 50 feet maximum length (per RS-232 industry specification - greater lengths are not recommended) RS-485 Network Cable • two ...
Information Regarding Future Change in Modem Support in Doors.NET
End-of-Life for PXL and Entraguard Modem Communication Keri has decided to delay removing support for modem communication for PXL and Entraguard units to the next software release. Doors.NET v4.8.0 will be the last software revision that will support ...